Author Archives: howandsometimeswhy

About howandsometimeswhy

https://howandsometimeswhy.wordpress.com

A new light & coat rack for the rear entryway

This rear entryway was my big project this last weekend.  When we moved into our house, the kitchen was tiny and had no cupboard space.  So we put a cabinet I had fixed up to use as a linen closet in the kitchen to use as a pantry. The landlord had our kitchen remodeled shortly after we moved in, but even with the extra cupboard space we decided that we wanted to keep the pantry.  With 5 adults living in the house, we figured it would be helpful to have some extra storage space for canned & dry goods. There wasn’t a good place for it in the kitchen, but in the rear entryway it would fit in the “coat closet” which was just a nook with a hanger bar and a high shelf.

This left us with a couple issues.  There was no light in the rear entry way, and now no place to hang coats.  Since I build both of those, I wanted to make a really rad industrial looking light and a rad coat rack made from bike parts and scrap metal pieces.  Well I ended up using a light fixture that was given to me in a tub of scrap metal.  It just seemed like the perfect light for that space. Even the colors matched.

OLYMPUS DIGITAL CAMERA

I’ve made a few switch boxes. When I want to put up a light fixture that you’d normally wire into the wall, but I can’t wire into the wall (because I’m a renter), I add a power cord with a switch box that can be mounted to the wall. If you don’t mind some exposed cord or a switch box on (instead of in) the wall, you can put a light fixture just about anywhere like this.

OLYMPUS DIGITAL CAMERA

In the rear entryway there is only one outlet that I use for the battery charger for my drill.  Since I would be using that outlet for my light and I still wanted to plug in my charger, I added an outlet to the switch box. The only real issue with this was that the box I picked up at the thrift store to use for this purpose was quite brittle. It looked pretty sturdy, but the wood split really easily. The entire top broke apart when I tried to drill a hole for the outlet, so I had to make some alterations to the original plan. It didn’t go together as easily as I expected, but I got it figured out. I just ran a sturdy lamp cord from there to where the light would be, holding it to the wall and ceiling with wire clips. Then I attached and hung the light fixture. Voila! We now had light for our pantry and I still had a place to plug in my charger.

OLYMPUS DIGITAL CAMERA

I really wanted to make some fancy coat racks, but it was just too easy to grab the hooks I’d salvaged from somewhere, screw them to the boards I’d salvaged from somewhere else and screw them to the wall.  It kind of fits with the saying, “The cobbler’s kids have no shoes.”  I always have all these ideas to make these fantastic things for our house, but when it comes time to actually build something for the house, I often end up making something pretty basic and utilitarian while I sell the coolest stuff I make.

Advertisements

How to Build a Cartbike

Cartbike Building Misadventurescartbikefrontside

(From Resist Zine #42)

I wrote this article many years ago, and to be perfectly honest… this isn’t the best cargo bike design.  However, this is one of the most popular articles I’ve ever written, so I thought I’d copy it here before I let the website where it is hosted die. Also, although it’s not the best designs, I’ve never seen another bike like this that can be built without welding which is a HUGE thing for someone without access to a welder.

For months Dan, Gus, Ben, Lisa & myself have been talking about building bicycles. I’ve mentioned before about me & Ben’s obsession with High Wheeler/Penny Farthing bikes. But neither of us knew how to weld, and we were having trouble figuring out all the details. So gradually, our focus shifted towards more utilitarian bicycles. Mostly pickup/truck bikes and cart bikes. We still were planning on doing welding though. Two people offered their assistance. Since Gus was as excited about the prospects as we were, it seemed like things would work. Once problem still remained. Gus didn’t have equipment, and the equipment at the community house where Dan lives was frozen in the garage. (The garage door couldn’t be moved for at least a month due to inches of ice around it) And we didn’t even know if we had the right equipment, because the only person who ever used it was gone for 5 months or more.
But when I ran across plans for a bicycle cart with no need for welding, ideas started churning. I didn’t like the plans, and they were kind of incomplete besides. But the basic idea that I latched onto was the use of U-clamps. A lot could be accomplished with those little wonders. The plans I found (they were either in Seedhead, Luddite Tech Zine or How 2 Zine.) suggested U-clamping forks to the side of a cart. We thought they’d move around too much and decided to try an axle (still using u-clamps to attach everything.) Their plans also called for some weird bent pipe contraption for steering. We decided to clamp the forks directly to the cart. This of course was all before we even had a cart in our possession. So it was all just speculation. Then we got our hands on some carts & Monday, got together for our first building session.

Gus towed a cart I’d left in Ben’s backyard over to my garage where we had plenty of parts and tools. We set about to finding pieces to put it together. We wanted a girls frame, so it’d be easy to get on and off. I didn’t have many, but we found a nice yellow one with no wheels or handlebars (or neck.) We found a back wheel and a couple front ones and started piecing it together It was about 4 hours that night, and mostly we just learned what wouldn’t work The allthread axle wasn’t the same thread as bicycle axles, so we had to jerry-rig it. I’ll save you the boring details of how that worked, because it ended up that the axle was too flimsy anyway. We tried to clamp the forks to the cart & had trouble there too. First we clamped it too low so that the pedals hit the ground, and we didn’t clamp it to main braces, so it broke the little welds on the cart. We had a brain storming session and put the parts away for the night.
cartinjury-1(Left:Picture from before brakes, & shifters were hooked up)I had to work the next day, so I gave Ben the key to the garage and showed him where the tools were. When I got home, they were putting the finishing touches on the basic design. I’ll give details on it’s assembly later. We took it for a test drive, and it was hella hard to drive! Wow! It took muscle to steer, and if you steered too sharp, it would tip over. And when you started to steer, it would pull even harder in that direction, so that you had to hold it back. At this point it had no brakes or gears. We had Lisa sit in it, since she was smallest. With a load, it was much easier to drive. We each took turns in it, and even with 165 pounds, it held up and drove fine. So then we brought it back to the garage and put a neck on it, which we clamped to the grocery cart for extra support and to attach the gear shifters to. (You should definitely have some gears on a cart bike.) We hooked up a back brake, which was also attached to the handle.

cartgus_ben_lisa-1

HOW TO BUILD YOUR OWN CARTBIKE

cartblack_textOkay, the first thing you’re going to have to do is get your hands on a cart. Metal ones are the only ones worth grabbing. I say, grab the biggest one you can find (but then I’ve never tried a small one.) Once you have that, you just grab yourself a hacksaw, and cut the basket off the bottom half of the cart. Just cut the four legs as close as you can to the basket. We also took the plastic handle off the cart, so that whoever originally owned the cart wouldn’t come after us trying to get it back. Take off any identifying marks, even if you dumpstered the thing. (rather than finding it on the side of the road or in a vacant lot or something.)

Next you’re going to need an adult sized bike to attach the cart to. I would highly suggest a women’s bike, since they’re much easier to get on and off of. I would also highly suggest that it be a 10 speed, since you’ll be happy to have the extra gears when you’re trying to pedal a basket full of groceries (or bricks, or people, or whatever) uphill.

Here’s a list of other things you’ll need to complete this project:

  • 6 or more small U-clamps (about an inch across)
  • 1 large U-clamp (big enough to fit around the head tube of your bike)
  • 2 matching front wheels & coinciding forks. (I would suggest at least 26inch wheels)
  • 2-4 hose clamps
  • 1 tin can

cartbikeforkshighlightedTake the forks and wheels and position them on the sides of the cart. You can screw around with this and try to figure out where they work best, but we found that the forks should stick past the bottom of the cart a couple inches, and should be pretty close to the back. One reason for this is that most of a cart is composed of weak little bars. If you attach the forks to those, the little welds will break, and it won’t be very strong. There are only a few strong bars that forks should be attached to. We chose a point near the back where some of the main supports are. Two of these strong bars crossed each other, and we put the U-clamps there. Put the U-clamps on, and tighten them down a bit. Make sure the cart sits level, and then tighten everything up. (I’ve highlighted the strong bars red, so they’re more visible in the picture. Notice the clamps (circled in yellow) are all attached to at least one of these.)

cartbikeforks-1Now, pull the front wheel off your bike. Remove the front brake, and both the brake handles. Now spread open the neck and remove your handlebars. (You’ll want to leave the neck, as you’ll be using it later. Also, using the handlebars to spread the neck open will make the job easier later on.)

 

cartbikehandlehighlighted_4199437_origWe tried to file the dropouts on the fork wide enough to accept the bar that runs across the bottom of the back of the basket, but gave up as we were in such a hurry to get the thing done. It evidently didn’t need to be done, but I think it might be a good idea anyway. So then you just turn the forks around, so they’re backwards and center them on the bar that runs across the bottom of the back of the cart. Use a U-clamp on each side of the fork near the bottom to attach it to a strong part of the back of the cart. Then use your big U-clamp to attach the neck to the back part of the cart. To make the attachment just a little more secure, we spread open the neck, and twisted the two pieces of the handle with a channel locks so they would slide into it, then tightened it up. To get a really tight fit, we would have needed some old tubing or tin can strips or something, but we left it as is. We also attached our gear shift levers to the neck. Because the backs of most carts flap open, you’ll need to use a few hose clamps to hold it shut. We put a couple on the bottom, and a couple on the sides.

Now you’ve kind of got a choice with the brakes. You can just leave off the front one, and attach the back handle to the cart like we did. Or you can put brakes on both the forks attached to the cart, and have them up in front where all the stopping power is. This is what I would have done, but the bike I was using didn’t have any brakes, and I had trouble scrounging up even one. This is where that tin can will come in handy. You’ll have to cut strips of it to wrap around the cart handle, so you can tightly attach the brake handles. In the pictures, it looks like we duct taped ours on, but that’s just there to cover the edges of the tin can. Some grips would make the handle a bit more comfortable. (maybe some of those foam 10 speed ones or something)

I haven’t gone into every single detail about putting one of these together, because every single bike/cart combination is going to be different. With each you’ll encounter your own special brand of problems along the way. If you’ve never worked on a bike before, this might not be the project for you. Probably learning to adjust your brakes & gears, and change your tires is a good place to start. If you’ve done some work on bikes, this should come pretty easy for you. The hardest part for us was coming up with the basic design, and doing it without any welds. We’ve fixed that problem for you. Now go to it!
cartbikefull4-1Just to let you know, our concern about the forks moving was well founded. Our forks do move a bit, but if the bike is moving forward, and especially with a load, the problem is self-correcting. It has yet to be a real problem. These things are pretty difficult to drive. I found that it’s much easier to steer by leaning, than by trying to turn the cart. The problem is that you have to shift your weight the opposite of the way you want to go. It’s sort of difficult to explain, but once you have yours built, you’ll see what I mean. It’s definitely not built for speed. In order to keep control, you have to move sort of slow. It’s good for getting loads of stuff (like groceries) but I wouldn’t want to use it as an every day bike (unless I was hauling a lot of stuff every day, and then I would build a trailer.)

Build it and they will…

 

ride it, and they will…

CRASH IT!

Then Bring it to the Grocery Store and Load it up



Fixing A Cabinet

I’m not really sure why I wrote this up, other than the fact that I like to work on stuff and I like to write about it.  It’s just a little project I did recently.  It’s nothing super fancy.  I didn’t take a cabinet and turn it into a magic wardrobe or anything but I did take a crapped out piece of furniture and make it usable.

While dropping off my friend David at his house, I saw a shelf sitting in the garbage.  I’d been thinking about how I could use some more shelving in the garage, and I’d just recently purchased a truck so I had plenty of room to haul it home.  I asked David if he would help me load it up.  When we got over there, it turned out to be a cabinet, not a shelf.  We had been looking at the back side of it.

OLYMPUS DIGITAL CAMERA

It wasn’t in particularly good shape when I got it.  The shelves were sitting at the bottom of the cabinet because they’d been held up by shelf brackets that were falling off.  The hardboard back was in pretty sad shape too.  The shell and doors were in decent shape though.  I changed my mind about using it in the garage when I found out it was a cabinet.  The bathroom in our basement, where our bedroom is, had no shelves and there wasn’t really any closet space down there at all.  We needed a place to keep towels and bedding and this seemed like it might just do the job.

OLYMPUS DIGITAL CAMERA

The first thing was those shelf brackets needed to come out.  They’d been screwed to the back of the cabinet which was mostly dilapidated hardboard.  The upper screws went all the way into the braces on the back, but the bottoms were pretty much swinging free.  Most of the screws easily turned out by hand.

OLYMPUS DIGITAL CAMERA

Next I had to do something about that hardboard on the back.  It was warped, water stained, and had holes poked through it.  I took off the door handles, which I wanted to replace anyway, and laid the cabinet face down in the driveway.  I used a pry bar to remove the braces on the back side, then pulled the nails so I could reuse them.  Next the actual hardboard came off.  I just tipped the cabinet on its side and pushed off the hardboard from the inside. It was in such sad shape that most of the nails just popped right through and I ended up going back and having to remove them all with a little nail puller. Then I had to turn it face down again and trim away the paint along the edges with a utility knife.

OLYMPUS DIGITAL CAMERA

Once it was off, I was trying to find a piece of plywood or something that I could put on the back. I wasn’t really having much luck finding anything in garage.  Then I noticed the fake wood paneling I had sitting around.  It’s kind of embarrassing really.  When I bought a house with my ex-wife about 10 years ago, I put up a wall in the basement to separate the laundry/utility room from the rest of the basement.  Since I was going to hang cupboards anyway, I just used paneling.  Well, these were scraps I’d been saving for 10 years!  I have used quite a few of those scraps and think I’m actually reaching the end of my stockpile, but it’s pretty silly that I’ve held onto it for that long! I asked Jodi if she was okay with the wood paneling, and of course she didn’t care.  I had two panels and they were somehow nearly a perfect fit.  I think I trimmed the end off one piece.

OLYMPUS DIGITAL CAMERA

Jodi had bought me a finishing nailer shortly before I started this project, so when it came time to nail those pieces on, I plugged it in and just kept pulling the trigger. That made super quick work of putting the back on.  I could have done it with the nails that I saved, but this helped me get things done before the sun went down.  Next I put the braces back on, using the nails that I saved when I pulled them off.

OLYMPUS DIGITAL CAMERA

OLYMPUS DIGITAL CAMERA

When I originally thought about using this cabinet for our bathroom, I thought about a spot in the actual bathroom where I thought it would fit.  Then I looked and realized that cabinet was way too wide for it. Then I thought of the space in front of the ‘closet’ I’d just made.  (Really just an open space between the bathroom and bedroom walls where I’d added some shelves.)  If I put wheels on the cabinet, we could put it there and it would hide the shelves and be right outside the bathroom door.  In order to add wheels to it, I had to add something to the bottom to screw them too.  A couple little pieces of scrap 2×4 were cut to length, nailed together and screwed to the base on either side.  Then I screwed on some industrial metal rollers I’d saved from this weird contraption I found in the alley one day.  Yes, yet another thing I’d held onto for way too long.  Well as it turned out, after doing all that, the shelf didn’t quite fit the way I’d hoped so I ended up taking the wheels off and putting it some place more permanent.

OLYMPUS DIGITAL CAMERA

At this point, it was getting dark and I was ready to call it a night, so I had Jodi help me carry it downstairs.  That turned out to be a really silly thing to do, because downstairs away from my tools it took me weeks to get around to finishing it up.  Today I finally got around to installing the shelves.  It consisted of cutting a piece of scrap wood into 11 inch lengths, sanding them and painting them white.  I didn’t HAVE to paint them white, but most of the cabinet was, so I figured I might as well since I had a can of white spray paint handy.  Waiting for the paint to dry was probably the longest part of this part.  I predrilled them and then some quick work with a tape measure, a square and an electric driver had the supports attached to the sides of the shelf.

OLYMPUS DIGITAL CAMERA

I threw in the shelves that came with it, and it was good to go.  I looked for something to replace the handles with, but I didn’t want to just throw on some cupboard handles or drawer pulls or something.  I want to make something custom, so the handles will wait until I get that figured out.

open-door

Until then, here it is holding the towels and blankets that used to be strewn around our bedroom.


DIY Chicken Water Heater

IMG_0027b

The ladies have NO interest in getting their feet in the snow

We’ve been flying by the seat of our pants pretty much from the get-go with our chickens.  We’d been trying to get chickens for a couple years, but things just kept falling through.  We finally decided that we’d just order them even though we had to move again, and they were going to show up a few days after we moved.  We were tired of waiting for the perfect timing; we’d just pull the trigger and make the timing work.  Still neck deep in boxes, we picked up our day old chicks.  Fortunately, that meant we had plenty of boxes to make our brooder out of.  We’d read far enough into our chicken books to know what we needed to do.

We did plan ahead for some things; others caught us a bit off guard.  One of those was a water heater.  We live in Minnesota, so we knew that we were eventually going to need something to keep the water from freezing in the winter, but we’d purchased the chicks in the spring so it wasn’t at the top of our priority list.  We started talking about it again as the weather got cool, but fall lasted surprisingly long for Minnesota.  All of a sudden we were hit with a cold snap, and their water started freezing.  It wasn’t freezing solid, but freezing enough around the edges that we had to go out once or twice a day to make sure that they still had liquid water.  The heated version of our water font ran about $50, and of course money was tight when the cold snap hit, so we were figuring out who got paid next so we could purchase it.  In the meantime I started trying to think up my own system for keeping the water from freezing.  I came up with an idea, but I wanted to make sure that it was a viable option before I did it so I went online to check it out.  Why I didn’t immediately look online for “DIY chicken water heaters” is beyond me.  I guess I’m still of the mindset that I need to figure it out for myself.  I ended up finding a water heater idea that I liked better than mine and changing it a bit to fit the materials I had on hand, and to make it a bit safer.  I had all of the materials on hand, but it probably would have run $5 if I had to purchase the items.

Here’s what you’ll need to make one:

  • 1 lamp holder
  • Scrap of wood (about 10×10”)
  • extension cord
  • 8x8x8 concrete block
  • 2 wood screws
  • Light bulb (about 60w)

Center your concrete block on your scrap of wood and trace the opening onto the wood. (My concrete block isn’t an 8x8x8″ block. It was actually a leftover piece from building this shelf: /building-a-custom-cinder-block-shelf/)

OLYMPUS DIGITAL CAMERA

Cut the receptacle end off your extension cord leaving the plug and about 6 feet of cord.  Separate the cord sides of the last 2 – 3inches of cord. You can use a sharp knife if you need to, but make sure not to expose the wire inside.  Strip the covering from the last half inch of wire.

OLYMPUS DIGITAL CAMERA

Cut a groove in the bottom of your lamp holder for the cord to pass through.  I cut 2 slits with a saw and then broke the piece out using pliers.

OLYMPUS DIGITAL CAMERA

Attach the wire to your lamp holder.  This is as simple as loosening the screws on the bottom, wrapping the wire around them, and then retightening them.

OLYMPUS DIGITAL CAMERA

Once your cord is securely attached, you can attach your lamp holder to the wooden base with your wood screws.

OLYMPUS DIGITAL CAMERA

Your concrete block should already have a little grove, but you’ll need to make it a little bigger so the wire can pass through it.  My daughter did this part with a hammer and chisel in about a minute.

OLYMPUS DIGITAL CAMERA

All there is left is to set the block over the lamp holder, making sure the wire passes through the groove.  Insert a light bulb, and plug it in.

(EDIT! We had some trouble with water condensing and dripping onto the bulb which would then break.  This problem was easily solved by placing a large mouth pint mason jar over the bulb.  We haven’t had a bulb break since and a 78watt bulb has always kept the water from completely freezing)

OLYMPUS DIGITAL CAMERA

The water font sits on top of the brick, and the heat from the light bulb keeps the water from completely freezing.  (This is why you need an incandescent bulb)  One thing we realized after a few days is that the water condenses on the bottom of the font and drips on the light bulb, which then breaks.  You don’t get a lot of water dripping, but one drop on a hot bulb will break it., so we fixed that by setting a wide mouth mason jar over the bulb.

 

When I originally made this I ran a drop cord under the door to plug it in.  Since then I’ve used added an outlet to the chicken coop, and used wire clips to attach the cord to the base of the heater as well as the wall.  I didn’t want loose wires dangling around in there.


Make Cheap Clamps from PVC Pipe

I really don’t like PVC.  I’ve gone over the reasons for this in How and Why: A Do-it-yourself Guide, but suffice it to say that it’s anything but environmentally friendly.  However, when we moved into our new house there was a bunch of PVC in the garage.  Yesterday we were going to do some truck camping, but our truck doesn’t have a window on the topper so I wanted a way to cover the opening in case in rained.  (Or as it happened, in case it was windy and cold)  I grabbed a tarp, but I needed a way to hold it on so I made up these PVC clips in about 2 minutes.

How to Make a PVC Clip

1. Cut a section of PVC pipe about 2 inches wide

2. Cut the PVC so that the circle opens

These work great for holding tarps on cars, or tablecloths on picnic tables, holding things while glue dries, or any number of things.  They’re really handy to have in your trunk or in your camping box.

I hate to encourage anybody to buy new PVC but if you’ve got some sitting around or pull some out of a dumpster, this is a really handy thing to make out of it.

IMG_1253IMG_1249 IMG_1250 IMG_1251


Seating A Tubeless (cart) Tire

Here’s a quick little trick for you. (If you don’t want to read the whole story, skip to the step by step below)

I found this 2 wheel cart in the garbage at one point.  The only thing that seemed to be wrong with it was that it was missing a wheel.  I figured it was about a $70 or $80 cart that probably needed a $5 or 10 wheel and tire, so I brought it home.  It sat for years.  I brought it with when I moved.  It sat for another year until I was about to move again and I thought, “This would come in handy when we move.”  So I went to Home Depot to buy a wheel & tire.  I didn’t think they would have it, but they did!  What they did NOT have was the compression nut that holds the wheel on.  The guy I asked about it (who inconsequentially was me 20 years ago, except he had a bit more swagger) actually KNEW something! I HATE going to Home Depot, but for a year it was about a mile from my house and the only ‘hardware’ store in NE Minneapolis. I go to hardware stores a LOT, so I ended up at Home Depot quite a bit.  Anyway, unlike most of the employees whose method of helping is to blindly search with you, this guy actually knew where the item was SUPPOSED to be, but informed me that they’d removed a whole drawer from the hardware section.  Yet another reason to hate Home Despot.  They carry the wheel to fix a cart, but not the nut to the hold the wheel on! Awesome! Later in the week I went to Menards and found the wheel/tire assembly AND the nut.

I got home and it took longer to remove the packaging than to actually install the wheel.  The only thing left to do was pump up the other tire, which I decided to do this morning when I got out the pump for my bicycle.  I started to pump and realized there was no tube and the tire was completely unseated from the rim.  I’ve had this happen before with wheelbarrow and other tires, and it can be nearly impossible to get the tire to reseat.  When I was trying to reseat the wheelbarrow tire, I tried something I’d seen on a video.  You spray starter fluid inside the tire and then light it.  When it lights it quickly expands seating the tire.  I could never get that to work, and I’ve tried it on a few different tire/rim combos.

When I was a kid my dad taught me how to seat my own car tires.  I had a 77 Dodge van that was perpetually getting flats for a while.  We thought someone in our townhouse complex didn’t like my eyesore of a van and kept letting the air out.  After spending $10 a half a dozen times or so to have a shop reseat the tire, my dad told me that I could reseat it myself with dish soap and an air compressor.  You just squirt dish soap along the bead of the tire and then with a good quick compressor, inflate the tire.  If the compressor is strong enough (like a gas station compressor), the tire will balloon out against the rim and seal.  Later I ended up having to bring my wheel in again and the new guy who worked on it told me, “Your rim was so rusty I’m surprised it held air at all!  I cleaned it up for you and it should be fine now.”  Yeah, so thanks to the guy who fixed my flat tire half a dozen times or more but never fixed the actual problem!

This might work with a wheelbarrow or cart wheel, but they also usually unseat on both sides of the wheel rather than just one like my van tires.  Today I took the advice from my dad and combined it with something I saw my ex-father-in-law do once.  He was trying it on a motorcycle tire and I’m not sure if it worked for him, but it worked for me.

Okay, I’m done with story-time, here’s the


Step by Step

  1. Clean the outside of the bead (the bead is the raised section at the center of the tire)
    Unseated Tire
  2. Squirt a decent amount of dish soap along the top of the bead. (make sure that it’s coated all the way around)
    Put dishsoap on bead
  3. Do the other side if necessary
  4. Wrap a ratcheting strap around the tire (I wrapped it 3 times)
    Wrap ratcheting strap around tire
  5. Attach the hooks together and start to tighten the strap with the ratchet until the center of the tire starts to depress. At that point, both of the beads should be in contact with rim.  If not, tighten it a bit more.
    Wrap ratcheting strap around tire
  6. Once the tire is contacting the rim on both sides, pump it up.
    Pump it up
  7. Remove the strap and you’re ready to go
    Ready to roll

It seems really simple, but it worked and it saved me from having to buy anything else.  And I didn’t need to go find a compressor either.


Charcoal (Grill) or Bon-Fire Starters

So I’ve seen these firestarters around that are half a toilet paper tube stuffed with shredded paper and wax.  I’ve never actually used one, but I’ve seen them at military surplus stores and the like.  I came up with one that I feel is even better, mostly because it uses things that you probably already have and throw away.  I mean you could make the traditional ones by shredding junk mail and melting old candles, but wax is messy to work with and these ones practically make themselves.

We don’t eat a ton of bacon at our house, but we do have some every week or two.  We also don’t use a lot of paper towels, but this is one thing we use them for.  We put down a couple squares on a plate to soak up the grease.  I got the idea for these from using those paper towels as fire starters.  Then I got the idea to make something you could easily store and transport.  The thing that really pushed me to try this was a friend who hates using lighter fluid when cooking with charcoal because it flavors the food.

These are pretty much one of the simplest things ever to make.  When you’re done making bacon:

  1. Stuff the grease soaked paper towels in a toilet paper tube (or a section of paper towel tube). 2 towels is a pretty perfect fit.
  2. Pour liquid grease in both ends of the tube until the paper towel is soaked. (In my experience ½ pound of cooked bacon yields enough grease for 2-3 tubes
  3. Set somewhere and allow to cool.

There’s not much more to it than the normal clean-up after making bacon.

The thing I really like about these is that you can use them to start charcoal without using lighter fluid.  The first time I tried one of these was when we barbecued with my friend who hates lighter fluid.  Just pull a bit of paper towel out the end of the tube so you have something to light.  Set it on a piece of charcoal (so when the grease starts to run out, it doesn’t just drip into the bottom of the grill) and then just build up a pyramid of coal around it and light it.  This doesn’t light quite as fast as lighter fluid, but it doesn’t impart any chemical taste to your food.

If you’re using it to light a bon fire, it works pretty much the same.  Put it on top of a larger piece of wood then put smaller pieces of wood around it.  It’ll get your fire going pretty darn quick.